Pressure Tank Repair in Palatka
Pressure tank repair is the fix when your Palatka well pump clicks on and off every few seconds or the shower turns hot and cold with every pressure swing. We test the air charge, the bladder and the switch, then recharge or replace the tank before the short cycling wears out your pump.
Seven days a week, 7 a.m. to 9 p.m. Licensed, bonded and insured. Free estimates.

Signs your pressure tank is failing
A failing tank rarely leaves you dry at first. It makes the pump work harder until something else breaks.
- The pump clicks on and off every few seconds while water runs
- Pressure swings up and down in the shower
- The gauge needle jumps instead of moving steadily
- Taps spurt or sputter when you first open them
- The tank sounds solid and full when you knock near the top
- Rust, sweating or a leak at the base of the tank
What a pressure tank actually does
Inside the tank, a rubber bladder or diaphragm separates water from a cushion of pressurized air. When the pump runs, it pushes water into the bladder and squeezes the air. When you open a tap, that air pushes the water back out, so the pump can rest.
When the air charge leaks away or the bladder tears, the tank fills with water and the cushion is gone. Now the pump has to start every time anyone opens a tap, and each start is wear on the motor.
How we fix it
- 1
Shut off and drain
We cut power to the pump and drain the tank so we can read the true air charge.
- 2
Check the charge
We measure the air pressure and compare it to the pressure switch setting.
- 3
Test the bladder
If water comes out of the air valve, the bladder has failed and the tank needs replacing.
- 4
Recharge or replace
A sound tank gets recharged. A failed one gets a new Pentair tank sized to your pump.
- 5
Set the switch
We set the pressure switch to match, then watch the pump run full cycles with you.
Why a bad tank is really a pump problem
A submersible pump is built to start, run a good long cycle and shut off. Short cycling turns that into dozens of quick starts an hour, and the heat from every start adds up in the motor.
Fixing a waterlogged tank now is how you avoid pulling a burned-out pump later. If the clicking has been going on for months, we will check the pump too.
Pressure tank questions
Can a waterlogged tank be repaired?
If the bladder is intact and the tank only lost its air charge, we can recharge it. If the bladder has torn, the tank needs replacing.
How big should my pressure tank be?
Big enough to give your pump a long run each cycle. We size the tank to the pump's flow, not to the space in the closet.
Why won't my well pump build pressure?
When the gauge climbs slowly or stalls below the shutoff point, the usual causes are a worn pump, a leak on the pressure side, a check valve that lets water fall back down the well, or a tank that has lost its air charge. We test each of those before we replace anything.
What does the pressure switch do?
It turns the pump on when the pressure at the tank drops to the low setting and off when it reaches the high one. Burned or pitted contacts in that switch are one of the most common reasons a pump stops starting.
How long do pressure tanks last?
It depends on the water and how hard the system works. Rust at the base or a failed bladder means it is time.
Can you replace the tank on the first visit?
When we have the right tank on the truck, yes. Otherwise we come back the next day.
More help with a Palatka well
Well pump repair in Palatka
Pumps, tanks and switches fixed seven days a week, 7 a.m. to 9 p.m.
No water from your well
What to check first when the taps go dry, and what usually failed.
Palatka well water problems
Rotten egg smell, orange stains, scale and bacteria, explained.
Stop the clicking before it costs you a pump
Call us seven days a week. Free estimate, written quote, then the fix.
Monday to Sunday, 7 a.m. to 9 p.m.
